If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#16
|
|||
|
|||
Cannot see 1 of 3 computers
On Wed, 2 Mar 2005 18:01:01 -0800, Ron Smith
wrote: Chuck, OK, here goes again -- sorry, I may have messed up the previous word wrap settings. Also before I post tht ipconfig stuff, you mentioned I only needed Client ..., File and Print..., and Internet Protocol in Properties -- well in addition to those (and the IPV6 which I removed), I have a whole bunch of extra stuff on the laptop (Network Monitor Driver, NW Link Net BIOS, NW Link IPX/SPX/Net Bios Compatible Transport Protocol). SNIP Ron, Interesting that the laptop has (had?) IPX/SPX and NetBIOS. With superfluous protocols, your network can get a little flaky - for instance, name to address resolution might use any protocol in any order. If the browser uses multiple protocols, things could get weird too. Let's enumerate your problems. Did you copy browstat.exe onto your computers? Is it in a path folder? Please do that, then proceed. Take the following code (everything inside the "#####"). (Please verify computer names and ip addresses). Open Notepad. Ensure that Format - Word Wrap is not checked. Highlight then Copy the code (Ctrl-C), precisely as it is keyed, and Paste (Ctrl-V) into Notepad. Verify, and correct, names and addresses if necessary. Save the Notepad file as "cdiag.cmd", as type "All Files", into the root folder "C:\". Run it by Start - Run - "c:\cdiag". Wait patiently. When Notepad opens up displaying c:\cdiag.txt, first check Format and ensure that Word Wrap is NOT checked! Then, copy the entire contents (Ctrl-A Ctrl-C) and paste (Ctrl-V) into your next post. Do this from all computers, please, with all computers powered up and online. ##### @echo off set FullTarget1=Ron 192.168.0.102 set FullTarget2=pavilion 192.168.0.100 set FullTarget3=claudette 192.168.0.101 set FullTarget4= set FullTargets=%FullTarget1% %FullTarget2% %FullTarget3% %FullTarget4% set PingTargets=127.0.0.1 192.168.0.1 Set Version=V1.07b @echo CDiagnosis %Version% c:\cdiag.txt @echo Start diagnosis for %computername% (Targets %FullTargets%) c:\cdiag.txt @echo. c:\cdiag.txt browstat status c:\cdiag.txt @echo. c:\cdiag.txt ping 66.94.230.32 c:\cdiag.txt for %%a in (%FullTargets% %PingTargets%) do ( @echo. c:\cdiag.txt @echo Target %%a c:\cdiag.txt @echo. c:\cdiag.txt @echo "ping %%a" c:\cdiag.txt @echo. c:\cdiag.txt ping %%a c:\cdiag.txt @echo. c:\cdiag.txt @echo "net view %%a" c:\cdiag.txt @echo. c:\cdiag.txt net view %%a c:\cdiag.txt ) @echo End diagnosis for %computername% c:\cdiag.txt notepad c:\cdiag.txt :EOF ##### -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
Ads |
#17
|
|||
|
|||
Cannot see 1 of 3 computers
Sorry, got an interruption -- more data coming -- soon.
"Chuck" wrote: On Wed, 2 Mar 2005 18:01:01 -0800, Ron Smith wrote: Chuck, OK, here goes again -- sorry, I may have messed up the previous word wrap settings. Also before I post tht ipconfig stuff, you mentioned I only needed Client ..., File and Print..., and Internet Protocol in Properties -- well in addition to those (and the IPV6 which I removed), I have a whole bunch of extra stuff on the laptop (Network Monitor Driver, NW Link Net BIOS, NW Link IPX/SPX/Net Bios Compatible Transport Protocol). SNIP Ron, Interesting that the laptop has (had?) IPX/SPX and NetBIOS. With superfluous protocols, your network can get a little flaky - for instance, name to address resolution might use any protocol in any order. If the browser uses multiple protocols, things could get weird too. Let's enumerate your problems. Did you copy browstat.exe onto your computers? Is it in a path folder? Please do that, then proceed. Take the following code (everything inside the "#####"). (Please verify computer names and ip addresses). Open Notepad. Ensure that Format - Word Wrap is not checked. Highlight then Copy the code (Ctrl-C), precisely as it is keyed, and Paste (Ctrl-V) into Notepad. Verify, and correct, names and addresses if necessary. Save the Notepad file as "cdiag.cmd", as type "All Files", into the root folder "C:\". Run it by Start - Run - "c:\cdiag". Wait patiently. When Notepad opens up displaying c:\cdiag.txt, first check Format and ensure that Word Wrap is NOT checked! Then, copy the entire contents (Ctrl-A Ctrl-C) and paste (Ctrl-V) into your next post. Do this from all computers, please, with all computers powered up and online. ##### @echo off set FullTarget1=Ron 192.168.0.102 set FullTarget2=pavilion 192.168.0.100 set FullTarget3=claudette 192.168.0.101 set FullTarget4= set FullTargets=%FullTarget1% %FullTarget2% %FullTarget3% %FullTarget4% set PingTargets=127.0.0.1 192.168.0.1 Set Version=V1.07b @echo CDiagnosis %Version% c:\cdiag.txt @echo Start diagnosis for %computername% (Targets %FullTargets%) c:\cdiag.txt @echo. c:\cdiag.txt browstat status c:\cdiag.txt @echo. c:\cdiag.txt ping 66.94.230.32 c:\cdiag.txt for %%a in (%FullTargets% %PingTargets%) do ( @echo. c:\cdiag.txt @echo Target %%a c:\cdiag.txt @echo. c:\cdiag.txt @echo "ping %%a" c:\cdiag.txt @echo. c:\cdiag.txt ping %%a c:\cdiag.txt @echo. c:\cdiag.txt @echo "net view %%a" c:\cdiag.txt @echo. c:\cdiag.txt net view %%a c:\cdiag.txt ) @echo End diagnosis for %computername% c:\cdiag.txt notepad c:\cdiag.txt :EOF ##### -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#18
|
|||
|
|||
Cannot see 1 of 3 computers
cdiags coming below:
cdiag out for Computer A ------------ CDiagnosis V1.07b Start diagnosis for RON (Targets Ron 192.168.0.102 pavilion 192.168.0.100 claudette 192.168.0.101 ) Status for domain MSHOME on transport \Device\NetBT_Tcpip_{813B86EA-F666-4FA6-A7A4-F43458710402} Browsing is active on domain. Master browser name is: RON Master browser is running build 2600 1 backup servers retrieved from master RON \\RON There are 2 servers in domain MSHOME on transport \Device\NetBT_Tcpip_{813B86EA-F666-4FA6-A7A4-F43458710402} There are 1 domains in domain MSHOME on transport \Device\NetBT_Tcpip_{813B86EA-F666-4FA6-A7A4-F43458710402} Pinging 66.94.230.32 with 32 bytes of data: Reply from 66.94.230.32: bytes=32 time=65ms TTL=45 Reply from 66.94.230.32: bytes=32 time=65ms TTL=45 Reply from 66.94.230.32: bytes=32 time=68ms TTL=45 Reply from 66.94.230.32: bytes=32 time=73ms TTL=44 Ping statistics for 66.94.230.32: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 65ms, Maximum = 73ms, Average = 67ms Target Ron "ping Ron" Pinging Ron [192.168.0.102] with 32 bytes of data: Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Ping statistics for 192.168.0.102: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view Ron" Shared resources at Ron Ron's Computer - 11/26/04 - 1G Mem, 200G HD - $979.00 Share name Type Used as Comment ------------------------------------------------------------------------------- Apple IIe Disk EPSONSty Print EPSON Stylus Photo RX600 HP LaserJet 2100 PCL6 Print HP LaserJet 2100 PCL6 HP LaserJet 2100 Series PS Print HP LaserJet 2100 Series PS SharedDocs Disk The command completed successfully. Target 192.168.0.102 "ping 192.168.0.102" Pinging 192.168.0.102 with 32 bytes of data: Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Ping statistics for 192.168.0.102: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view 192.168.0.102" Shared resources at 192.168.0.102 Ron's Computer - 11/26/04 - 1G Mem, 200G HD - $979.00 Share name Type Used as Comment ------------------------------------------------------------------------------- Apple IIe Disk EPSONSty Print EPSON Stylus Photo RX600 HP LaserJet 2100 PCL6 Print HP LaserJet 2100 PCL6 HP LaserJet 2100 Series PS Print HP LaserJet 2100 Series PS SharedDocs Disk The command completed successfully. Target pavilion "ping pavilion" Pinging pavilion [192.168.0.100] with 32 bytes of data: Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Ping statistics for 192.168.0.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view pavilion" Shared resources at pavilion HPhost Share name Type Used as Comment ------------------------------------------------------------------------------- My Picturesx Disk My Playlists Disk SharedDocs Disk The command completed successfully. Target 192.168.0.100 "ping 192.168.0.100" Pinging 192.168.0.100 with 32 bytes of data: Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Ping statistics for 192.168.0.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view 192.168.0.100" Shared resources at 192.168.0.100 HPhost Share name Type Used as Comment ------------------------------------------------------------------------------- My Picturesx Disk My Playlists Disk SharedDocs Disk The command completed successfully. Target claudette "ping claudette" Pinging claudette [192.168.0.101] with 32 bytes of data: Request timed out. Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Request timed out. Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Ping statistics for 192.168.0.101: Packets: Sent = 4, Received = 2, Lost = 2 (50% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 2ms, Average = 2ms "net view claudette" Shared resources at claudette compaq centrino laptop Share name Type Used as Comment ------------------------------------------------------------------------------- Printer Print Family Tree Maker Printer SharedDocs Disk temp Disk The command completed successfully. Target 192.168.0.101 "ping 192.168.0.101" Pinging 192.168.0.101 with 32 bytes of data: Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Request timed out. Request timed out. Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Ping statistics for 192.168.0.101: Packets: Sent = 4, Received = 2, Lost = 2 (50% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 2ms, Average = 2ms "net view 192.168.0.101" Shared resources at 192.168.0.101 compaq centrino laptop Share name Type Used as Comment ------------------------------------------------------------------------------- Printer Print Family Tree Maker Printer SharedDocs Disk temp Disk The command completed successfully. Target 127.0.0.1 "ping 127.0.0.1" Pinging 127.0.0.1 with 32 bytes of data: Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Ping statistics for 127.0.0.1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view 127.0.0.1" Shared resources at 127.0.0.1 Ron's Computer - 11/26/04 - 1G Mem, 200G HD - $979.00 Share name Type Used as Comment ------------------------------------------------------------------------------- Apple IIe Disk EPSONSty Print EPSON Stylus Photo RX600 HP LaserJet 2100 PCL6 Print HP LaserJet 2100 PCL6 HP LaserJet 2100 Series PS Print HP LaserJet 2100 Series PS SharedDocs Disk The command completed successfully. Target 192.168.0.1 "ping 192.168.0.1" Pinging 192.168.0.1 with 32 bytes of data: Reply from 192.168.0.1: bytes=32 time=2ms TTL=127 Reply from 192.168.0.1: bytes=32 time=1ms TTL=127 Reply from 192.168.0.1: bytes=32 time=1ms TTL=127 Reply from 192.168.0.1: bytes=32 time=1ms TTL=127 Ping statistics for 192.168.0.1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 2ms, Average = 1ms "net view 192.168.0.1" End diagnosis for RON cdiagout for Computer B ------------- CDiagnosis V1.07b Start diagnosis for PAVILION (Targets Ron 192.168.0.102 pavilion 192.168.0.100 claudette 192.168.0.101 ) Status for domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} Browsing is active on domain. Master browser name is: RON Could not connect to registry, error = 53 Unable to determine build of browser master: 53 \\\\RON . Version:05.01 Flags: 51203 NT POTENTIAL MASTER 1 backup servers retrieved from master RON \\RON There are 2 servers in domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} There are 1 domains in domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} Pinging 66.94.230.32 with 32 bytes of data: Reply from 66.94.230.32: bytes=32 time=65ms TTL=44 Reply from 66.94.230.32: bytes=32 time=65ms TTL=45 Reply from 66.94.230.32: bytes=32 time=69ms TTL=45 Reply from 66.94.230.32: bytes=32 time=67ms TTL=45 Ping statistics for 66.94.230.32: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 65ms, Maximum = 69ms, Average = 66ms Target Ron "ping Ron" Pinging Ron [192.168.0.102] with 32 bytes of data: Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Ping statistics for 192.168.0.102: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view Ron" Shared resources at Ron Ron's Computer - 11/26/04 - 1G Mem, 200G HD - $979.00 Share name Type Used as Comment ------------------------------------------------------------------------------- Apple IIe Disk EPSONSty Print EPSON Stylus Photo RX600 HP LaserJet 2100 PCL6 Print HP LaserJet 2100 PCL6 HP LaserJet 2100 Series PS Print HP LaserJet 2100 Series PS SharedDocs Disk The command completed successfully. Target 192.168.0.102 "ping 192.168.0.102" Pinging 192.168.0.102 with 32 bytes of data: Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Reply from 192.168.0.102: bytes=32 time1ms TTL=128 Ping statistics for 192.168.0.102: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view 192.168.0.102" Shared resources at 192.168.0.102 Ron's Computer - 11/26/04 - 1G Mem, 200G HD - $979.00 Share name Type Used as Comment ------------------------------------------------------------------------------- Apple IIe Disk EPSONSty Print EPSON Stylus Photo RX600 HP LaserJet 2100 PCL6 Print HP LaserJet 2100 PCL6 HP LaserJet 2100 Series PS Print HP LaserJet 2100 Series PS SharedDocs Disk The command completed successfully. Target pavilion "ping pavilion" Pinging pavilion [192.168.0.100] with 32 bytes of data: Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Ping statistics for 192.168.0.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view pavilion" Shared resources at pavilion HPhost Share name Type Used as Comment ------------------------------------------------------------------------------- My Picturesx Disk My Playlists Disk SharedDocs Disk The command completed successfully. Target 192.168.0.100 "ping 192.168.0.100" Pinging 192.168.0.100 with 32 bytes of data: Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Reply from 192.168.0.100: bytes=32 time1ms TTL=128 Ping statistics for 192.168.0.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view 192.168.0.100" Shared resources at 192.168.0.100 HPhost Share name Type Used as Comment ------------------------------------------------------------------------------- My Picturesx Disk My Playlists Disk SharedDocs Disk The command completed successfully. Target claudette "ping claudette" Pinging claudette [192.168.0.101] with 32 bytes of data: Request timed out. Request timed out. Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Request timed out. Ping statistics for 192.168.0.101: Packets: Sent = 4, Received = 1, Lost = 3 (75% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 2ms, Average = 2ms "net view claudette" Shared resources at claudette compaq centrino laptop Share name Type Used as Comment ------------------------------------------------------------------------------- Printer Print Family Tree Maker Printer SharedDocs Disk (UNC) temp Disk The command completed successfully. Target 192.168.0.101 "ping 192.168.0.101" Pinging 192.168.0.101 with 32 bytes of data: Reply from 192.168.0.101: bytes=32 time=5ms TTL=128 Request timed out. Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Request timed out. Ping statistics for 192.168.0.101: Packets: Sent = 4, Received = 2, Lost = 2 (50% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 5ms, Average = 3ms "net view 192.168.0.101" Shared resources at 192.168.0.101 compaq centrino laptop Share name Type Used as Comment ------------------------------------------------------------------------------- Printer Print Family Tree Maker Printer SharedDocs Disk temp Disk The command completed successfully. Target 127.0.0.1 "ping 127.0.0.1" Pinging 127.0.0.1 with 32 bytes of data: Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Ping statistics for 127.0.0.1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view 127.0.0.1" Target 192.168.0.1 "ping 192.168.0.1" Pinging 192.168.0.1 with 32 bytes of data: Reply from 192.168.0.1: bytes=32 time=1ms TTL=127 Reply from 192.168.0.1: bytes=32 time=1ms TTL=127 Reply from 192.168.0.1: bytes=32 time=1ms TTL=127 Reply from 192.168.0.1: bytes=32 time=1ms TTL=127 Ping statistics for 192.168.0.1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 1ms, Average = 1ms "net view 192.168.0.1" End diagnosis for PAVILION cdiag for Computer C ----------- CDiagnosis V1.07b Start diagnosis for CLAUDETTE (Targets Ron 192.168.0.102 pavilion 192.168.0.100 claudette 192.168.0.101 ) Status for domain MSHOME on transport \Device\NwlnkNb Browsing is active on domain. Master name cannot be determined from GetAdapterStatus. Using \\CLAUDETTE Master browser is running build 2600 1 backup servers retrieved from master CLAUDETTE \\CLAUDETTE There are 1 servers in domain MSHOME on transport \Device\NwlnkNb There are 1 domains in domain MSHOME on transport \Device\NwlnkNb Status for domain MSHOME on transport \Device\NetBT_Tcpip_{055EF24E-58C0-4E29-9889-94BD958371C3} Browsing is active on domain. Master browser name is: RON Could not connect to registry, error = 53 Unable to determine build of browser master: 53 \\\\RON . Version:05.01 Flags: 51203 NT POTENTIAL MASTER 1 backup servers retrieved from master RON \\RON There are 2 servers in domain MSHOME on transport \Device\NetBT_Tcpip_{055EF24E-58C0-4E29-9889-94BD958371C3} Unable to retrieve server list from RON: 64 Status for domain MSHOME on transport \Device\NwlnkIpx Browsing is NOT active on domain. Master name cannot be determined from GetAdapterStatus. Pinging 66.94.230.32 with 32 bytes of data: Reply from 66.94.230.32: bytes=32 time=67ms TTL=44 Reply from 66.94.230.32: bytes=32 time=75ms TTL=44 Reply from 66.94.230.32: bytes=32 time=69ms TTL=45 Reply from 66.94.230.32: bytes=32 time=67ms TTL=44 Ping statistics for 66.94.230.32: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 67ms, Maximum = 75ms, Average = 69ms Target Ron "ping Ron" Pinging Ron [192.168.0.102] with 32 bytes of data: Reply from 192.168.0.102: bytes=32 time=3ms TTL=128 Reply from 192.168.0.102: bytes=32 time=2ms TTL=128 Reply from 192.168.0.102: bytes=32 time=2ms TTL=128 Reply from 192.168.0.102: bytes=32 time=6ms TTL=128 Ping statistics for 192.168.0.102: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 6ms, Average = 3ms "net view Ron" Shared resources at Ron Ron's Computer - 11/26/04 - 1G Mem, 200G HD - $979.00 Share name Type Used as Comment ------------------------------------------------------------------------------- Apple IIe Disk EPSONSty Print EPSON Stylus Photo RX600 HP LaserJet 2100 PCL6 Print HP LaserJet 2100 PCL6 HP LaserJet 2100 Series PS Print HP LaserJet 2100 Series PS SharedDocs Disk The command completed successfully. Target 192.168.0.102 "ping 192.168.0.102" Pinging 192.168.0.102 with 32 bytes of data: Reply from 192.168.0.102: bytes=32 time=2ms TTL=128 Reply from 192.168.0.102: bytes=32 time=7ms TTL=128 Reply from 192.168.0.102: bytes=32 time=7ms TTL=128 Reply from 192.168.0.102: bytes=32 time=7ms TTL=128 Ping statistics for 192.168.0.102: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 7ms, Average = 5ms "net view 192.168.0.102" Shared resources at 192.168.0.102 Ron's Computer - 11/26/04 - 1G Mem, 200G HD - $979.00 Share name Type Used as Comment ------------------------------------------------------------------------------- Apple IIe Disk EPSONSty Print EPSON Stylus Photo RX600 HP LaserJet 2100 PCL6 Print HP LaserJet 2100 PCL6 HP LaserJet 2100 Series PS Print HP LaserJet 2100 Series PS SharedDocs Disk The command completed successfully. Target pavilion "ping pavilion" Pinging pavilion [192.168.0.100] with 32 bytes of data: Reply from 192.168.0.100: bytes=32 time=2ms TTL=128 Reply from 192.168.0.100: bytes=32 time=2ms TTL=128 Reply from 192.168.0.100: bytes=32 time=2ms TTL=128 Reply from 192.168.0.100: bytes=32 time=2ms TTL=128 Ping statistics for 192.168.0.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 2ms, Average = 2ms "net view pavilion" Shared resources at pavilion HPhost Share name Type Used as Comment ------------------------------------------------------------------------------- My Picturesx Disk My Playlists Disk SharedDocs Disk The command completed successfully. Target 192.168.0.100 "ping 192.168.0.100" Pinging 192.168.0.100 with 32 bytes of data: Reply from 192.168.0.100: bytes=32 time=2ms TTL=128 Reply from 192.168.0.100: bytes=32 time=2ms TTL=128 Reply from 192.168.0.100: bytes=32 time=3ms TTL=128 Reply from 192.168.0.100: bytes=32 time=7ms TTL=128 Ping statistics for 192.168.0.100: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 7ms, Average = 3ms "net view 192.168.0.100" Shared resources at 192.168.0.100 HPhost Share name Type Used as Comment ------------------------------------------------------------------------------- My Picturesx Disk My Playlists Disk SharedDocs Disk The command completed successfully. Target claudette "ping claudette" Pinging claudette [192.168.0.101] with 32 bytes of data: Reply from 192.168.0.101: bytes=32 time1ms TTL=128 Reply from 192.168.0.101: bytes=32 time1ms TTL=128 Reply from 192.168.0.101: bytes=32 time1ms TTL=128 Reply from 192.168.0.101: bytes=32 time1ms TTL=128 Ping statistics for 192.168.0.101: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view claudette" Shared resources at claudette compaq centrino laptop Share name Type Used as Comment ------------------------------------------------------------------------------- Printer Print Family Tree Maker Printer SharedDocs Disk temp Disk The command completed successfully. Target 192.168.0.101 "ping 192.168.0.101" Pinging 192.168.0.101 with 32 bytes of data: Reply from 192.168.0.101: bytes=32 time1ms TTL=128 Reply from 192.168.0.101: bytes=32 time1ms TTL=128 Reply from 192.168.0.101: bytes=32 time1ms TTL=128 Reply from 192.168.0.101: bytes=32 time1ms TTL=128 Ping statistics for 192.168.0.101: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view 192.168.0.101" Shared resources at 192.168.0.101 compaq centrino laptop Share name Type Used as Comment ------------------------------------------------------------------------------- Printer Print Family Tree Maker Printer SharedDocs Disk temp Disk The command completed successfully. Target 127.0.0.1 "ping 127.0.0.1" Pinging 127.0.0.1 with 32 bytes of data: Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Reply from 127.0.0.1: bytes=32 time1ms TTL=128 Ping statistics for 127.0.0.1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 0ms, Average = 0ms "net view 127.0.0.1" Shared resources at 127.0.0.1 compaq centrino laptop Share name Type Used as Comment ------------------------------------------------------------------------------- Printer Print Family Tree Maker Printer SharedDocs Disk temp Disk The command completed successfully. Target 192.168.0.1 "ping 192.168.0.1" Pinging 192.168.0.1 with 32 bytes of data: Reply from 192.168.0.1: bytes=32 time=3ms TTL=127 Reply from 192.168.0.1: bytes=32 time=3ms TTL=127 Reply from 192.168.0.1: bytes=32 time=3ms TTL=127 Reply from 192.168.0.1: bytes=32 time=7ms TTL=127 Ping statistics for 192.168.0.1: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 3ms, Maximum = 7ms, Average = 4ms "net view 192.168.0.1" End diagnosis for CLAUDETTE -- Ron -- End of cdiag's. "Chuck" wrote: On Wed, 2 Mar 2005 18:01:01 -0800, Ron Smith wrote: Chuck, OK, here goes again -- sorry, I may have messed up the previous word wrap settings. Also before I post tht ipconfig stuff, you mentioned I only needed Client ..., File and Print..., and Internet Protocol in Properties -- well in addition to those (and the IPV6 which I removed), I have a whole bunch of extra stuff on the laptop (Network Monitor Driver, NW Link Net BIOS, NW Link IPX/SPX/Net Bios Compatible Transport Protocol). SNIP Ron, Interesting that the laptop has (had?) IPX/SPX and NetBIOS. With superfluous protocols, your network can get a little flaky - for instance, name to address resolution might use any protocol in any order. If the browser uses multiple protocols, things could get weird too. Let's enumerate your problems. Did you copy browstat.exe onto your computers? Is it in a path folder? Please do that, then proceed. Take the following code (everything inside the "#####"). (Please verify computer names and ip addresses). Open Notepad. Ensure that Format - Word Wrap is not checked. Highlight then Copy the code (Ctrl-C), precisely as it is keyed, and Paste (Ctrl-V) into Notepad. Verify, and correct, names and addresses if necessary. Save the Notepad file as "cdiag.cmd", as type "All Files", into the root folder "C:\". Run it by Start - Run - "c:\cdiag". Wait patiently. When Notepad opens up displaying c:\cdiag.txt, first check Format and ensure that Word Wrap is NOT checked! Then, copy the entire contents (Ctrl-A Ctrl-C) and paste (Ctrl-V) into your next post. Do this from all computers, please, with all computers powered up and online. ##### @echo off set FullTarget1=Ron 192.168.0.102 set FullTarget2=pavilion 192.168.0.100 set FullTarget3=claudette 192.168.0.101 set FullTarget4= set FullTargets=%FullTarget1% %FullTarget2% %FullTarget3% %FullTarget4% set PingTargets=127.0.0.1 192.168.0.1 Set Version=V1.07b @echo CDiagnosis %Version% c:\cdiag.txt @echo Start diagnosis for %computername% (Targets %FullTargets%) c:\cdiag.txt @echo. c:\cdiag.txt browstat status c:\cdiag.txt @echo. c:\cdiag.txt ping 66.94.230.32 c:\cdiag.txt for %%a in (%FullTargets% %PingTargets%) do ( @echo. c:\cdiag.txt @echo Target %%a c:\cdiag.txt @echo. c:\cdiag.txt @echo "ping %%a" c:\cdiag.txt @echo. c:\cdiag.txt ping %%a c:\cdiag.txt @echo. c:\cdiag.txt @echo "net view %%a" c:\cdiag.txt @echo. c:\cdiag.txt net view %%a c:\cdiag.txt ) @echo End diagnosis for %computername% c:\cdiag.txt notepad c:\cdiag.txt :EOF ##### -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#19
|
|||
|
|||
Cannot see 1 of 3 computers
On Wed, 2 Mar 2005 21:11:02 -0800, Ron Smith
wrote: cdiags coming below: SNIP Ron, Very interesting results. 1) Both Pavilion and Claudette see Ron as the master browser (for Claudette, in NBT only). Neither Pavilion nor Claudette can access the registry in Ron, though ("error = 53"). An error 53 is "not found", indicating a name resolution issue. Status for domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} Browsing is active on domain. Master browser name is: RON Could not connect to registry, error = 53 Unable to determine build of browser master: 53 \\\\RON . Version:05.01 Flags: 51203 NT POTENTIAL MASTER 1 backup servers retrieved from master RON \\RON There are 2 servers in domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} There are 1 domains in domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} 2) None of the computers have any trouble displaying the share list on any other ("net view"). Both Ron and Pavilion, however, have trouble pinging Claudette. Pinging claudette [192.168.0.101] with 32 bytes of data: Request timed out. Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Request timed out. Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Ping statistics for 192.168.0.101: Packets: Sent = 4, Received = 2, Lost = 2 (50% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 2ms, Average = 2ms 3) Claudette shows itself as the master browser in IPX, but Ron as the master browser in NBT. Status for domain MSHOME on transport \Device\NwlnkNb Browsing is active on domain. Master name cannot be determined from GetAdapterStatus. Using \\CLAUDETTE Master browser is running build 2600 1 backup servers retrieved from master CLAUDETTE \\CLAUDETTE There are 1 servers in domain MSHOME on transport \Device\NwlnkNb There are 1 domains in domain MSHOME on transport \Device\NwlnkNb Status for domain MSHOME on transport \Device\NetBT_Tcpip_{055EF24E-58C0-4E29-9889-94BD958371C3} Browsing is active on domain. Master browser name is: RON Could not connect to registry, error = 53 Unable to determine build of browser master: 53 \\\\RON . Version:05.01 Flags: 51203 NT POTENTIAL MASTER 1 backup servers retrieved from master RON \\RON There are 2 servers in domain MSHOME on transport \Device\NetBT_Tcpip_{055EF24E-58C0-4E29-9889-94BD958371C3} Unable to retrieve server list from RON: 64 Status for domain MSHOME on transport \Device\NwlnkIpx Browsing is NOT active on domain. Master name cannot be determined from GetAdapterStatus. Issue 1 is most likely a misbehaving firewall. What firewalls do you have, or have ever had, on Ron? Ron is running XP SP2 - is the File and Printer Sharing exception enabled? Also, look at registry key [HKLM\System\CurrentControlSet\Control\Lsa], value restrictanonymous. http://www.microsoft.com/windows2000/techinfo/reskit/en-us/default.asp?url=/windows2000/techinfo/reskit/en-us/regentry/46688.asp http://www.jsifaq.com/subf/tip2600/rh2625.htm http://support.microsoft.com/?id=246261 http://support.microsoft.com/?id=296403 The above articles refer to Windows 2000. Remember WinXP is NT V5.1, and Win2K is NT V5.0. Have you used the Registry Editor before? If not, it's a scary tool, but it's pretty simple once you get used to it. Here are a couple articles that might help: http://www.microsoft.com/windowsxp/home/using/productdoc/en/default.asp?url=/windowsxp/home/using/productdoc/en/tools_regeditors.asp http://www.annoyances.org/exec/show/registry Just remember to backup the key (create a registry patch) for [HKLM\System\CurrentControlSet\Control\Lsa] before making any changes, if appropriate. From the Annoyances article: You can create a Registry patch by opening the Registry Editor, selecting a branch, and choosing Export from the File menu. Then, specify a filename, and press OK. You can then view the Registry patch file by opening it in Notepad (right-click on it and select Edit). Again, just double-click on a Registry patch file (or use Import in the Registry Editor's File menu) to apply it to the registry. Issue 2 - dropped packets between Ron / Pavilion and Claudette - is a network (probably wireless) issue. Have you loaded the most up to date drivers for the wireless card? Issue 3 - Claudette is running a browser. You need to either un install IPX/SPX, or Stop then Disable the browser service on Claudette, or both. If you're going to have 2 computers running a browser (recommended for a 3 computer LAN), then Pavilion should be the backup, not Claudette. Do you really need IPX / SPX on Claudette? What other network is it used on? -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#20
|
|||
|
|||
Cannot see 1 of 3 computers
OK, Chuck -- thanks again for the help and analysis. Let me respond to some
of your questions: 1) Just a couple of minutes before I read your post, I sent off a Firewall question to the D-Link tech support guys. I don't understand their firewall setup -- don't even know how it is working -- and don't know why it would single out computer A on the home net. It has occured to me that this looks like some sort of firewall problem -- that's how firealls are supposed to work, isn't it. As far as the Windows XP Firewall is concerned, File and Printer Sharing, Remote Assistance, and UPnP Framework(?) is enabled on Computer A (Ron), and the same on Computer C (claudette) -- Zone Alarm running on Computer B (Pavilion). I haven't done anything exotic, anywhere, because things are starting to get complicated -- so I pretty much go with default settings whenever possible. I have done Registry things, several years ago. I will look into the things you have suggested, carefully. As this is a new computer, as of December, 2004, I wouldn't think too much is screwed up yet. 2) Yeah, dropped packets, I didn't want to throw that into the situation. I have been having that problem since Nov, 2003 -- when I purchased the laptop for my wife -- and set up a 2 computer network. It is beyond annoying -- she pretty much does't use it much except for email. It hangs up when surfing the Internet (i.e. screen updates just stop, and recover much later after timeouts, I think -- maybe because of packet drops?). The most annoying things is the email operation. The system does not seem to have problems receiving email, but when sending email, we get lots of Server timed out errors. I have had to re-send the email as many as 20 (yeah, 20) times before it will go out -- beyond frustrating. The laptop has the Centrino chip set in it -- can that stuff be updated. As far as the email problem is concerned, it has gotten better ever since last week when I rearranged my computer area -- moving my newer computer onto my main table and relocating the older computer to another table a few feet away. Ever since I have had the router, it has been positioned right next to a 23" CRT monitor -- whereas it is now behind my 17" LCD monitor and the 23" monitor on its way to good will, once I get all of my files transferred off of it. I am now wondering if the large CRT was affecting the wireless transmissions. Sometimes I wonder how the laptop is even working when it seems to be dropping probably 50% of the pings. 3) Regarding the laptop, I don't need any of the TCP stuff I mentioned in my previous note -- at least as far as I know of -- it is not used on any other networks -- I don't even know what that other stuff is. As I said, I don't start changing default things because I generally don't know what I am changing. However, as I said, I am not doing anything exotic (just using laptop in my home for wireless access and non-Internet stand-alone use) -- so if I don't need it, I am more than willing to delete it. As far as you know, should I go ahead and uninstall the Network Monitor and the other 2 NW Link middle-ware programs. OK, sorry for the long response. I will look into the Registry things you suggested and get back to you -- but hope I don't have to change anything. As I said, I have only been using this system for a few months, so don't know what I could have done to mess it up. -- Ron "Chuck" wrote: On Wed, 2 Mar 2005 21:11:02 -0800, Ron Smith wrote: cdiags coming below: SNIP Ron, Very interesting results. 1) Both Pavilion and Claudette see Ron as the master browser (for Claudette, in NBT only). Neither Pavilion nor Claudette can access the registry in Ron, though ("error = 53"). An error 53 is "not found", indicating a name resolution issue. Status for domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} Browsing is active on domain. Master browser name is: RON Could not connect to registry, error = 53 Unable to determine build of browser master: 53 \\\\RON . Version:05.01 Flags: 51203 NT POTENTIAL MASTER 1 backup servers retrieved from master RON \\RON There are 2 servers in domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} There are 1 domains in domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} 2) None of the computers have any trouble displaying the share list on any other ("net view"). Both Ron and Pavilion, however, have trouble pinging Claudette. Pinging claudette [192.168.0.101] with 32 bytes of data: Request timed out. Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Request timed out. Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Ping statistics for 192.168.0.101: Packets: Sent = 4, Received = 2, Lost = 2 (50% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 2ms, Average = 2ms 3) Claudette shows itself as the master browser in IPX, but Ron as the master browser in NBT. Status for domain MSHOME on transport \Device\NwlnkNb Browsing is active on domain. Master name cannot be determined from GetAdapterStatus. Using \\CLAUDETTE Master browser is running build 2600 1 backup servers retrieved from master CLAUDETTE \\CLAUDETTE There are 1 servers in domain MSHOME on transport \Device\NwlnkNb There are 1 domains in domain MSHOME on transport \Device\NwlnkNb Status for domain MSHOME on transport \Device\NetBT_Tcpip_{055EF24E-58C0-4E29-9889-94BD958371C3} Browsing is active on domain. Master browser name is: RON Could not connect to registry, error = 53 Unable to determine build of browser master: 53 \\\\RON . Version:05.01 Flags: 51203 NT POTENTIAL MASTER 1 backup servers retrieved from master RON \\RON There are 2 servers in domain MSHOME on transport \Device\NetBT_Tcpip_{055EF24E-58C0-4E29-9889-94BD958371C3} Unable to retrieve server list from RON: 64 Status for domain MSHOME on transport \Device\NwlnkIpx Browsing is NOT active on domain. Master name cannot be determined from GetAdapterStatus. Issue 1 is most likely a misbehaving firewall. What firewalls do you have, or have ever had, on Ron? Ron is running XP SP2 - is the File and Printer Sharing exception enabled? Also, look at registry key [HKLM\System\CurrentControlSet\Control\Lsa], value restrictanonymous. http://www.microsoft.com/windows2000/techinfo/reskit/en-us/default.asp?url=/windows2000/techinfo/reskit/en-us/regentry/46688.asp http://www.jsifaq.com/subf/tip2600/rh2625.htm http://support.microsoft.com/?id=246261 http://support.microsoft.com/?id=296403 The above articles refer to Windows 2000. Remember WinXP is NT V5.1, and Win2K is NT V5.0. Have you used the Registry Editor before? If not, it's a scary tool, but it's pretty simple once you get used to it. Here are a couple articles that might help: http://www.microsoft.com/windowsxp/home/using/productdoc/en/default.asp?url=/windowsxp/home/using/productdoc/en/tools_regeditors.asp http://www.annoyances.org/exec/show/registry Just remember to backup the key (create a registry patch) for [HKLM\System\CurrentControlSet\Control\Lsa] before making any changes, if appropriate. From the Annoyances article: You can create a Registry patch by opening the Registry Editor, selecting a branch, and choosing Export from the File menu. Then, specify a filename, and press OK. You can then view the Registry patch file by opening it in Notepad (right-click on it and select Edit). Again, just double-click on a Registry patch file (or use Import in the Registry Editor's File menu) to apply it to the registry. Issue 2 - dropped packets between Ron / Pavilion and Claudette - is a network (probably wireless) issue. Have you loaded the most up to date drivers for the wireless card? Issue 3 - Claudette is running a browser. You need to either un install IPX/SPX, or Stop then Disable the browser service on Claudette, or both. If you're going to have 2 computers running a browser (recommended for a 3 computer LAN), then Pavilion should be the backup, not Claudette. Do you really need IPX / SPX on Claudette? What other network is it used on? -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#21
|
|||
|
|||
Cannot see 1 of 3 computers
Chuck, just a quick response.
I do not see a restrictanonymous entry in the Lsa of my Registry. -- Ron "Chuck" wrote: On Wed, 2 Mar 2005 21:11:02 -0800, Ron Smith wrote: cdiags coming below: SNIP Ron, Very interesting results. 1) Both Pavilion and Claudette see Ron as the master browser (for Claudette, in NBT only). Neither Pavilion nor Claudette can access the registry in Ron, though ("error = 53"). An error 53 is "not found", indicating a name resolution issue. Status for domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} Browsing is active on domain. Master browser name is: RON Could not connect to registry, error = 53 Unable to determine build of browser master: 53 \\\\RON . Version:05.01 Flags: 51203 NT POTENTIAL MASTER 1 backup servers retrieved from master RON \\RON There are 2 servers in domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} There are 1 domains in domain MSHOME on transport \Device\NetBT_Tcpip_{3F2DCAAD-DF3F-4F44-B920-FB44E017DEFD} 2) None of the computers have any trouble displaying the share list on any other ("net view"). Both Ron and Pavilion, however, have trouble pinging Claudette. Pinging claudette [192.168.0.101] with 32 bytes of data: Request timed out. Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Request timed out. Reply from 192.168.0.101: bytes=32 time=2ms TTL=128 Ping statistics for 192.168.0.101: Packets: Sent = 4, Received = 2, Lost = 2 (50% loss), Approximate round trip times in milli-seconds: Minimum = 2ms, Maximum = 2ms, Average = 2ms 3) Claudette shows itself as the master browser in IPX, but Ron as the master browser in NBT. Status for domain MSHOME on transport \Device\NwlnkNb Browsing is active on domain. Master name cannot be determined from GetAdapterStatus. Using \\CLAUDETTE Master browser is running build 2600 1 backup servers retrieved from master CLAUDETTE \\CLAUDETTE There are 1 servers in domain MSHOME on transport \Device\NwlnkNb There are 1 domains in domain MSHOME on transport \Device\NwlnkNb Status for domain MSHOME on transport \Device\NetBT_Tcpip_{055EF24E-58C0-4E29-9889-94BD958371C3} Browsing is active on domain. Master browser name is: RON Could not connect to registry, error = 53 Unable to determine build of browser master: 53 \\\\RON . Version:05.01 Flags: 51203 NT POTENTIAL MASTER 1 backup servers retrieved from master RON \\RON There are 2 servers in domain MSHOME on transport \Device\NetBT_Tcpip_{055EF24E-58C0-4E29-9889-94BD958371C3} Unable to retrieve server list from RON: 64 Status for domain MSHOME on transport \Device\NwlnkIpx Browsing is NOT active on domain. Master name cannot be determined from GetAdapterStatus. Issue 1 is most likely a misbehaving firewall. What firewalls do you have, or have ever had, on Ron? Ron is running XP SP2 - is the File and Printer Sharing exception enabled? Also, look at registry key [HKLM\System\CurrentControlSet\Control\Lsa], value restrictanonymous. http://www.microsoft.com/windows2000/techinfo/reskit/en-us/default.asp?url=/windows2000/techinfo/reskit/en-us/regentry/46688.asp http://www.jsifaq.com/subf/tip2600/rh2625.htm http://support.microsoft.com/?id=246261 http://support.microsoft.com/?id=296403 The above articles refer to Windows 2000. Remember WinXP is NT V5.1, and Win2K is NT V5.0. Have you used the Registry Editor before? If not, it's a scary tool, but it's pretty simple once you get used to it. Here are a couple articles that might help: http://www.microsoft.com/windowsxp/home/using/productdoc/en/default.asp?url=/windowsxp/home/using/productdoc/en/tools_regeditors.asp http://www.annoyances.org/exec/show/registry Just remember to backup the key (create a registry patch) for [HKLM\System\CurrentControlSet\Control\Lsa] before making any changes, if appropriate. From the Annoyances article: You can create a Registry patch by opening the Registry Editor, selecting a branch, and choosing Export from the File menu. Then, specify a filename, and press OK. You can then view the Registry patch file by opening it in Notepad (right-click on it and select Edit). Again, just double-click on a Registry patch file (or use Import in the Registry Editor's File menu) to apply it to the registry. Issue 2 - dropped packets between Ron / Pavilion and Claudette - is a network (probably wireless) issue. Have you loaded the most up to date drivers for the wireless card? Issue 3 - Claudette is running a browser. You need to either un install IPX/SPX, or Stop then Disable the browser service on Claudette, or both. If you're going to have 2 computers running a browser (recommended for a 3 computer LAN), then Pavilion should be the backup, not Claudette. Do you really need IPX / SPX on Claudette? What other network is it used on? -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#22
|
|||
|
|||
Cannot see 1 of 3 computers
On Thu, 3 Mar 2005 09:27:08 -0800, Ron Smith
wrote: OK, Chuck -- thanks again for the help and analysis. Let me respond to some of your questions: 1) Just a couple of minutes before I read your post, I sent off a Firewall question to the D-Link tech support guys. I don't understand their firewall setup -- don't even know how it is working -- and don't know why it would single out computer A on the home net. It has occured to me that this looks like some sort of firewall problem -- that's how firealls are supposed to work, isn't it. As far as the Windows XP Firewall is concerned, File and Printer Sharing, Remote Assistance, and UPnP Framework(?) is enabled on Computer A (Ron), and the same on Computer C (claudette) -- Zone Alarm running on Computer B (Pavilion). I haven't done anything exotic, anywhere, because things are starting to get complicated -- so I pretty much go with default settings whenever possible. I have done Registry things, several years ago. I will look into the things you have suggested, carefully. As this is a new computer, as of December, 2004, I wouldn't think too much is screwed up yet. 2) Yeah, dropped packets, I didn't want to throw that into the situation. I have been having that problem since Nov, 2003 -- when I purchased the laptop for my wife -- and set up a 2 computer network. It is beyond annoying -- she pretty much does't use it much except for email. It hangs up when surfing the Internet (i.e. screen updates just stop, and recover much later after timeouts, I think -- maybe because of packet drops?). The most annoying things is the email operation. The system does not seem to have problems receiving email, but when sending email, we get lots of Server timed out errors. I have had to re-send the email as many as 20 (yeah, 20) times before it will go out -- beyond frustrating. The laptop has the Centrino chip set in it -- can that stuff be updated. As far as the email problem is concerned, it has gotten better ever since last week when I rearranged my computer area -- moving my newer computer onto my main table and relocating the older computer to another table a few feet away. Ever since I have had the router, it has been positioned right next to a 23" CRT monitor -- whereas it is now behind my 17" LCD monitor and the 23" monitor on its way to good will, once I get all of my files transferred off of it. I am now wondering if the large CRT was affecting the wireless transmissions. Sometimes I wonder how the laptop is even working when it seems to be dropping probably 50% of the pings. 3) Regarding the laptop, I don't need any of the TCP stuff I mentioned in my previous note -- at least as far as I know of -- it is not used on any other networks -- I don't even know what that other stuff is. As I said, I don't start changing default things because I generally don't know what I am changing. However, as I said, I am not doing anything exotic (just using laptop in my home for wireless access and non-Internet stand-alone use) -- so if I don't need it, I am more than willing to delete it. As far as you know, should I go ahead and uninstall the Network Monitor and the other 2 NW Link middle-ware programs. OK, sorry for the long response. I will look into the Registry things you suggested and get back to you -- but hope I don't have to change anything. As I said, I have only been using this system for a few months, so don't know what I could have done to mess it up. Ron, It is a pleasure to read a post here with detail and coherence. No problems about its length. And what you said was well said. 1) I think you have a common misconception about routers and firewalls. The firewall (if it has one, and not all NAT router do) on a NAT router is between the WAN (Internet) and LAN (your computers). There is no firewall between your computers themselves, that's a part of the router. Your computers are interconnected thru a switch, which provides no filtering. What model D-Link is it? Pray that the registry setting is the problem. With every thing working on your LAN, save the 3 minor issues I identified, there's not going to be too many things to look for. If you're absolutely sure that there's no firewalls. What AntiVirus or other security package do you have? 2) You have a wireless problem for sure. Since you have a D-Link router (WAP) talking to an Intel client, lots of luck getting D-Link or Intel to fix it. It's quite possible the monitor is part of the problem. Also any microwave oven, or cordless phone, could be a problem. How far is the router to the laptop typically? Any walls involved? A 1 foot wall causes way more than 1 foot of air, in signal degradation. Try another channel on the router - if on channel 1, move to 11. If on 11, move to 1. If on 6, move to 1 or 11 then the other. See if the signal improves. Also check the antenna direction, and elevation, for the router and laptop. Both antennas pointed vertically, and at the same height from the floor, is best. The closer the two are placed, with different elevation or antenna orientation, the better chance for signal loss. For more wireless help, try newsgroups alt.internet.wireless and microsoft.public.windows.networking.wireless. Also, the DSLReports Forums for D-Link and for Wireless Networking could be very helpful - there is a lot of expert presence there. http://www.dslreports.com/forum/dlink http://www.dslreports.com/forum/wlan http://www.dslreports.com/forum/wsecurity (this one for the long term) 3) Neither IPX/SPX/NetBEUI, nor the Network Monitor, should be necessary for your LAN. Just un install each (then reboot). You only need the following items in the list under Local Area Connection Properties: Client for Microsoft Networks File and Printer Sharing For Microsoft Networks QoS Packet Scheduler (optional) Internet Protocol (TCP/IP) Then, make sure that NetBIOS Over TCP/IP is enabled on all computers. Local Area Connection - Properties - TCP/IP - Properties - Advanced - WINS - Enable NetBIOS over TCP/IP. If the laptop is typically used in the same room with the router, I'd sooner clean up its network components stack than play with antennas / interference sources. But do check with Intel / laptop vendor / D-Link for newer drivers / firmware. -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#23
|
|||
|
|||
Cannot see 1 of 3 computers
On Thu, 3 Mar 2005 10:13:05 -0800, Ron Smith
wrote: Chuck, just a quick response. I do not see a restrictanonymous entry in the Lsa of my Registry. Dang. What AntiVirus package do you have? Look in "C:\WINDOWS\system32\drivers\etc" for files Hosts and LMHosts. Any entry in either (ignore "127.0.0.1 localhost")? Node Types (from IPConfig) are all Hybrid, and Unknown, no problem there. http://support.microsoft.com/?id=160177 -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#24
|
|||
|
|||
Cannot see 1 of 3 computers
Chuck-
1) OK, I understand what you are saying about the D-Link router. It is a DI-514 -- a pretty cheap router I picked up when we got my wife's laptop last Thanksgiving, 2003. And yes, good luck in getting anyone to spend any time on my problem. The D-Link people regularly blow me off, 3 or 4 times in the last year when I have tried to get the email send problem (20 times to send an email) resolved. I don't have a cordless phone and there is probably not a microwave issue. The problem is pretty much the same whether the laptop is located in another room or in the same room, approx. 6' from the router (no detactable difference). Also, the operation has been the same in another house (moved in May) -- so there has been no change in the wireless operation since I got the router, Nov, 2003. So now I have a new computer and a new house in the mix -- not much else to look at -- except the Router itself and the laptop. Which brings me to mention that I have been thinking about switching to another router -- they're not too expensive. Do you know about these things or have an opinion or experience with any of them -- I was wondering about the Linksys routers. I have the Semantec Norton 2004 90-day freebie Antivirus running on my new Computer A (Ron) -- the stuff that comes installed on a new computer. Actually, the update subscription expired last week (24th) -- and I am thinking I will probably move to the Norton Antivirus 2005, or possibly the Internet Security package which is their Antivirus packaged with their firewall. I suppose if I do that, I need to disable the Windows Firewall -- is that right -- any thoughts or recommendations. And as mentioned earlier, Windows Firewall is also running on Computer A (Ron). Freebies AVG Antivirus and Zone Alarm Firewall running on Computer B (pavilion) and only Windows Firewall running on the laptop, Computer C (claudette) -- plan on putting Antivirus software on that machine also, probably the same as I get for Computer A. 2) Regarding router comments -- I don't know how to change channels on the router. I don't see any switches on the router. Is that the channel 6 I see in the default router configuration software or is it something else -- which would mean I also have to change something else on the computer, doesn't it. As I mentioned earlier, my laptop is often located 6'-7' from the router. I think performance has improved since I moved my big CRT monitor, but it is still sparatic based on the ping statistics. (I just turned the CRT monitor off and tried the ping test -- no noticable change -- still fails approx. 50% of the time.) I'll look into the other forums you referenced -- thanks. 3) OK, I have uninstalled the IPX/SPX/NetBEUI and Network Monitor stuff. Ping responses didn't improve -- still failing roughly 50% of the time. One thing you mentioned is the "Enable NetBIOS over TCP/IP" setting. None of the computers have that option enabled. Als systems have the "Default: Use NetBIOS settings from the DHCP server. If static . . . . . " 4) And finally, there was't any restrictanonymous entry in the Lsa area of the Registry -- should there have been. -- Ron "Chuck" wrote: On Thu, 3 Mar 2005 09:27:08 -0800, Ron Smith wrote: OK, Chuck -- thanks again for the help and analysis. Let me respond to some of your questions: 1) Just a couple of minutes before I read your post, I sent off a Firewall question to the D-Link tech support guys. I don't understand their firewall setup -- don't even know how it is working -- and don't know why it would single out computer A on the home net. It has occured to me that this looks like some sort of firewall problem -- that's how firealls are supposed to work, isn't it. As far as the Windows XP Firewall is concerned, File and Printer Sharing, Remote Assistance, and UPnP Framework(?) is enabled on Computer A (Ron), and the same on Computer C (claudette) -- Zone Alarm running on Computer B (Pavilion). I haven't done anything exotic, anywhere, because things are starting to get complicated -- so I pretty much go with default settings whenever possible. I have done Registry things, several years ago. I will look into the things you have suggested, carefully. As this is a new computer, as of December, 2004, I wouldn't think too much is screwed up yet. 2) Yeah, dropped packets, I didn't want to throw that into the situation. I have been having that problem since Nov, 2003 -- when I purchased the laptop for my wife -- and set up a 2 computer network. It is beyond annoying -- she pretty much does't use it much except for email. It hangs up when surfing the Internet (i.e. screen updates just stop, and recover much later after timeouts, I think -- maybe because of packet drops?). The most annoying things is the email operation. The system does not seem to have problems receiving email, but when sending email, we get lots of Server timed out errors. I have had to re-send the email as many as 20 (yeah, 20) times before it will go out -- beyond frustrating. The laptop has the Centrino chip set in it -- can that stuff be updated. As far as the email problem is concerned, it has gotten better ever since last week when I rearranged my computer area -- moving my newer computer onto my main table and relocating the older computer to another table a few feet away. Ever since I have had the router, it has been positioned right next to a 23" CRT monitor -- whereas it is now behind my 17" LCD monitor and the 23" monitor on its way to good will, once I get all of my files transferred off of it. I am now wondering if the large CRT was affecting the wireless transmissions. Sometimes I wonder how the laptop is even working when it seems to be dropping probably 50% of the pings. 3) Regarding the laptop, I don't need any of the TCP stuff I mentioned in my previous note -- at least as far as I know of -- it is not used on any other networks -- I don't even know what that other stuff is. As I said, I don't start changing default things because I generally don't know what I am changing. However, as I said, I am not doing anything exotic (just using laptop in my home for wireless access and non-Internet stand-alone use) -- so if I don't need it, I am more than willing to delete it. As far as you know, should I go ahead and uninstall the Network Monitor and the other 2 NW Link middle-ware programs. OK, sorry for the long response. I will look into the Registry things you suggested and get back to you -- but hope I don't have to change anything. As I said, I have only been using this system for a few months, so don't know what I could have done to mess it up. Ron, It is a pleasure to read a post here with detail and coherence. No problems about its length. And what you said was well said. 1) I think you have a common misconception about routers and firewalls. The firewall (if it has one, and not all NAT router do) on a NAT router is between the WAN (Internet) and LAN (your computers). There is no firewall between your computers themselves, that's a part of the router. Your computers are interconnected thru a switch, which provides no filtering. What model D-Link is it? Pray that the registry setting is the problem. With every thing working on your LAN, save the 3 minor issues I identified, there's not going to be too many things to look for. If you're absolutely sure that there's no firewalls. What AntiVirus or other security package do you have? 2) You have a wireless problem for sure. Since you have a D-Link router (WAP) talking to an Intel client, lots of luck getting D-Link or Intel to fix it. It's quite possible the monitor is part of the problem. Also any microwave oven, or cordless phone, could be a problem. How far is the router to the laptop typically? Any walls involved? A 1 foot wall causes way more than 1 foot of air, in signal degradation. Try another channel on the router - if on channel 1, move to 11. If on 11, move to 1. If on 6, move to 1 or 11 then the other. See if the signal improves. Also check the antenna direction, and elevation, for the router and laptop. Both antennas pointed vertically, and at the same height from the floor, is best. The closer the two are placed, with different elevation or antenna orientation, the better chance for signal loss. For more wireless help, try newsgroups alt.internet.wireless and microsoft.public.windows.networking.wireless. Also, the DSLReports Forums for D-Link and for Wireless Networking could be very helpful - there is a lot of expert presence there. http://www.dslreports.com/forum/dlink http://www.dslreports.com/forum/wlan http://www.dslreports.com/forum/wsecurity (this one for the long term) 3) Neither IPX/SPX/NetBEUI, nor the Network Monitor, should be necessary for your LAN. Just un install each (then reboot). You only need the following items in the list under Local Area Connection Properties: Client for Microsoft Networks File and Printer Sharing For Microsoft Networks QoS Packet Scheduler (optional) Internet Protocol (TCP/IP) Then, make sure that NetBIOS Over TCP/IP is enabled on all computers. Local Area Connection - Properties - TCP/IP - Properties - Advanced - WINS - Enable NetBIOS over TCP/IP. If the laptop is typically used in the same room with the router, I'd sooner clean up its network components stack than play with antennas / interference sources. But do check with Intel / laptop vendor / D-Link for newer drivers / firmware. -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#25
|
|||
|
|||
Cannot see 1 of 3 computers
Chuck-
As in previous post, I am running Semantec Norton 2004 Antivirus with Windows Firewall. There are no entries in the lmhosts.sam file. The hosts file only contains the "127.0.0.1 localhost" entry that you mentioned -- nothing else. "Chuck" wrote: On Thu, 3 Mar 2005 10:13:05 -0800, Ron Smith wrote: Chuck, just a quick response. I do not see a restrictanonymous entry in the Lsa of my Registry. Dang. What AntiVirus package do you have? Look in "C:\WINDOWS\system32\drivers\etc" for files Hosts and LMHosts. Any entry in either (ignore "127.0.0.1 localhost")? Node Types (from IPConfig) are all Hybrid, and Unknown, no problem there. http://support.microsoft.com/?id=160177 -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#26
|
|||
|
|||
Cannot see 1 of 3 computers
On Thu, 3 Mar 2005 12:11:04 -0800, Ron Smith
wrote: Chuck- 1) OK, I understand what you are saying about the D-Link router. It is a DI-514 -- a pretty cheap router I picked up when we got my wife's laptop last Thanksgiving, 2003. And yes, good luck in getting anyone to spend any time on my problem. The D-Link people regularly blow me off, 3 or 4 times in the last year when I have tried to get the email send problem (20 times to send an email) resolved. I don't have a cordless phone and there is probably not a microwave issue. The problem is pretty much the same whether the laptop is located in another room or in the same room, approx. 6' from the router (no detactable difference). Also, the operation has been the same in another house (moved in May) -- so there has been no change in the wireless operation since I got the router, Nov, 2003. So now I have a new computer and a new house in the mix -- not much else to look at -- except the Router itself and the laptop. Which brings me to mention that I have been thinking about switching to another router -- they're not too expensive. Do you know about these things or have an opinion or experience with any of them -- I was wondering about the Linksys routers. I have the Semantec Norton 2004 90-day freebie Antivirus running on my new Computer A (Ron) -- the stuff that comes installed on a new computer. Actually, the update subscription expired last week (24th) -- and I am thinking I will probably move to the Norton Antivirus 2005, or possibly the Internet Security package which is their Antivirus packaged with their firewall. I suppose if I do that, I need to disable the Windows Firewall -- is that right -- any thoughts or recommendations. And as mentioned earlier, Windows Firewall is also running on Computer A (Ron). Freebies AVG Antivirus and Zone Alarm Firewall running on Computer B (pavilion) and only Windows Firewall running on the laptop, Computer C (claudette) -- plan on putting Antivirus software on that machine also, probably the same as I get for Computer A. 2) Regarding router comments -- I don't know how to change channels on the router. I don't see any switches on the router. Is that the channel 6 I see in the default router configuration software or is it something else -- which would mean I also have to change something else on the computer, doesn't it. As I mentioned earlier, my laptop is often located 6'-7' from the router. I think performance has improved since I moved my big CRT monitor, but it is still sparatic based on the ping statistics. (I just turned the CRT monitor off and tried the ping test -- no noticable change -- still fails approx. 50% of the time.) I'll look into the other forums you referenced -- thanks. 3) OK, I have uninstalled the IPX/SPX/NetBEUI and Network Monitor stuff. Ping responses didn't improve -- still failing roughly 50% of the time. One thing you mentioned is the "Enable NetBIOS over TCP/IP" setting. None of the computers have that option enabled. Als systems have the "Default: Use NetBIOS settings from the DHCP server. If static . . . . . " 4) And finally, there was't any restrictanonymous entry in the Lsa area of the Registry -- should there have been. Ron, 1) The DI-514 does have a small bit of firewall, but as I mentioned above, it applies to the WAN only. No firewall in the LAN, so no chance that your problem is there. I use Linksys myself, and have no problem to report with them in general. Asides that is, for the fact that my BEFSX41 turned into a brick when I tried to upgrade the firmware last week. Dunno whose fault that was, but it's dead. ( I have no idea whether the D-Link itself is responsible for your packet loss problem, nor whether a new Linksys will improve, but, as you say, they're cheap enough. And having a surplus (spare) router is never a bad idea, especially if you're like me and like to do firmware upgrades. The nice thing about Linksys is that the router log (intrusion detection) is probably more complete than most NAT routers. You can get free WallWatcher software to monitor traffic in and out of your LAN. Knowledge is one of the essential layers in a layered security policy IMHO, and WallWatcher will provide you pretty good knowledge about your LAN - WAN traffic. http://www.wallwatcher.com/ I asked about your AntiVirus with the hopes that you, like more than one previous poster in this forum, you'd turn out to have Norton Internet Security package, which includes Norton Personal Firewall. My experience with network issues like yours are causes like: - Physical: No network / inconsistent network - disconnected or bad cable. Or bad wireless connection. - Logical: Bad firewall. - Security: Setting like LSA: restrictanonymous. 2) You change the router channel from the router management screen, accessible thru your browser. Looking at the manual for the DI-514, this is probably :http://192.168.0.1". 3) The "Enable NetBIOS over TCP/IP" setting, if universally set to Default, is probably OK. But try changing them all to "Enable", just in case Ron is using SMB instead of NBT. I'm not done here yet, we've checked the most common solutions. I'll think a bit more, and see what else might be going wrong. Are you still getting "The network path was not found" when your Run "\\Ron"? That's at interesting odds with the CDiag for both Pavilion and Claudette: "net view Ron" Shared resources at Ron Ron's Computer - 11/26/04 - 1G Mem, 200G HD - $979.00 Share name Type Used as Comment ------------------------------------------------------------------------------- Apple IIe Disk EPSONSty Print EPSON Stylus Photo RX600 HP LaserJet 2100 PCL6 Print HP LaserJet 2100 PCL6 HP LaserJet 2100 Series PS Print HP LaserJet 2100 Series PS SharedDocs Disk The command completed successfully. Are all 3 computers in the same workgroup? What version - XP Home or Pro - on each? 4) An LSA: restrictanonymous = "1" or "2" would have been a good candidate for problem cause, a non-existent value is probably the same as a "0". Oh well. -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#27
|
|||
|
|||
Cannot see 1 of 3 computers
Chuck, may have missed your other question -- the NetBT entries -- or was it.
Anyway, I'm not sure what you were looking for there. There are a lot of REG_DWORD entries, but didn't see anything that looked like a Node Type. -- Ron "Chuck" wrote: On Thu, 3 Mar 2005 10:13:05 -0800, Ron Smith wrote: Chuck, just a quick response. I do not see a restrictanonymous entry in the Lsa of my Registry. Dang. What AntiVirus package do you have? Look in "C:\WINDOWS\system32\drivers\etc" for files Hosts and LMHosts. Any entry in either (ignore "127.0.0.1 localhost")? Node Types (from IPConfig) are all Hybrid, and Unknown, no problem there. http://support.microsoft.com/?id=160177 -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#28
|
|||
|
|||
Cannot see 1 of 3 computers
On Thu, 3 Mar 2005 13:49:02 -0800, Ron Smith
wrote: Chuck, may have missed your other question -- the NetBT entries -- or was it. Anyway, I'm not sure what you were looking for there. There are a lot of REG_DWORD entries, but didn't see anything that looked like a Node Type. Ron, The Node Type entry is in IPConfig: Windows IP Configuration Host Name . . . . . . . . . . . . : Ron Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Unknown Node Type describes how name to address resolution is done. http://support.microsoft.com/?id=160177 The NetBT entry I have only found in the Local Area Connection Properties wizard. It's either set as "Default", "Enabled", or "Disabled". The "Default" setting defers to the DHCP server, when there's a dedicated DHCP server on the LAN. I don't know that any NAT router DHCP server sets this value; most advice here will simply tell you to set it manually to "Enabled". If NBT is not enabled, you could be using SMB, I don't know if that's the problem here. http://support.microsoft.com/?id=315267 -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#29
|
|||
|
|||
Cannot see 1 of 3 computers
Chuck,
With all my checks and changes, the network seems to kind of drift in and out of operation -- but always in response to something I have done -- but always recoverable. Possible when I was getting Path not Found, it was one of the times when the network wasn't really quite working. But now, \\ron seems to be running on both computers B & C. It takes a while for the screen to come up, but a window pops up with "Ron's Computer -- 11/26/04 - 1GMem, 200G HD - $979.00 (ron)" in the Blue Window Frame at the top of the window. (This is the Computer description in Ron, except for the (ron) at the end.) Also, I didn't notice this before because the window pops up with the verbage on the left side of the screen, but when I click on the folders, and see the folders breakdown on the left, I see the Ron computer under the Network Places\....\Mshome\, (with the name above) along with claudette and pavilion. Also, under the computer name, I see an Apple IIe folder (an emulator - my son's work), a Shared Docs folder and a Printers and Faxes icon. That seems correct, as I marked the Apple IIe as shared, since I knew it didn't exist on the other computers and it would therefore help me to know I was looking at the Ron computer. This should be an important clue, shouldn't it. -- Ron "Chuck" wrote: On Thu, 3 Mar 2005 12:11:04 -0800, Ron Smith wrote: Chuck- 1) OK, I understand what you are saying about the D-Link router. It is a DI-514 -- a pretty cheap router I picked up when we got my wife's laptop last Thanksgiving, 2003. And yes, good luck in getting anyone to spend any time on my problem. The D-Link people regularly blow me off, 3 or 4 times in the last year when I have tried to get the email send problem (20 times to send an email) resolved. I don't have a cordless phone and there is probably not a microwave issue. The problem is pretty much the same whether the laptop is located in another room or in the same room, approx. 6' from the router (no detactable difference). Also, the operation has been the same in another house (moved in May) -- so there has been no change in the wireless operation since I got the router, Nov, 2003. So now I have a new computer and a new house in the mix -- not much else to look at -- except the Router itself and the laptop. Which brings me to mention that I have been thinking about switching to another router -- they're not too expensive. Do you know about these things or have an opinion or experience with any of them -- I was wondering about the Linksys routers. I have the Semantec Norton 2004 90-day freebie Antivirus running on my new Computer A (Ron) -- the stuff that comes installed on a new computer. Actually, the update subscription expired last week (24th) -- and I am thinking I will probably move to the Norton Antivirus 2005, or possibly the Internet Security package which is their Antivirus packaged with their firewall. I suppose if I do that, I need to disable the Windows Firewall -- is that right -- any thoughts or recommendations. And as mentioned earlier, Windows Firewall is also running on Computer A (Ron). Freebies AVG Antivirus and Zone Alarm Firewall running on Computer B (pavilion) and only Windows Firewall running on the laptop, Computer C (claudette) -- plan on putting Antivirus software on that machine also, probably the same as I get for Computer A. 2) Regarding router comments -- I don't know how to change channels on the router. I don't see any switches on the router. Is that the channel 6 I see in the default router configuration software or is it something else -- which would mean I also have to change something else on the computer, doesn't it. As I mentioned earlier, my laptop is often located 6'-7' from the router. I think performance has improved since I moved my big CRT monitor, but it is still sparatic based on the ping statistics. (I just turned the CRT monitor off and tried the ping test -- no noticable change -- still fails approx. 50% of the time.) I'll look into the other forums you referenced -- thanks. 3) OK, I have uninstalled the IPX/SPX/NetBEUI and Network Monitor stuff. Ping responses didn't improve -- still failing roughly 50% of the time. One thing you mentioned is the "Enable NetBIOS over TCP/IP" setting. None of the computers have that option enabled. Als systems have the "Default: Use NetBIOS settings from the DHCP server. If static . . . . . " 4) And finally, there was't any restrictanonymous entry in the Lsa area of the Registry -- should there have been. Ron, 1) The DI-514 does have a small bit of firewall, but as I mentioned above, it applies to the WAN only. No firewall in the LAN, so no chance that your problem is there. I use Linksys myself, and have no problem to report with them in general. Asides that is, for the fact that my BEFSX41 turned into a brick when I tried to upgrade the firmware last week. Dunno whose fault that was, but it's dead. ( I have no idea whether the D-Link itself is responsible for your packet loss problem, nor whether a new Linksys will improve, but, as you say, they're cheap enough. And having a surplus (spare) router is never a bad idea, especially if you're like me and like to do firmware upgrades. The nice thing about Linksys is that the router log (intrusion detection) is probably more complete than most NAT routers. You can get free WallWatcher software to monitor traffic in and out of your LAN. Knowledge is one of the essential layers in a layered security policy IMHO, and WallWatcher will provide you pretty good knowledge about your LAN - WAN traffic. http://www.wallwatcher.com/ I asked about your AntiVirus with the hopes that you, like more than one previous poster in this forum, you'd turn out to have Norton Internet Security package, which includes Norton Personal Firewall. My experience with network issues like yours are causes like: - Physical: No network / inconsistent network - disconnected or bad cable. Or bad wireless connection. - Logical: Bad firewall. - Security: Setting like LSA: restrictanonymous. 2) You change the router channel from the router management screen, accessible thru your browser. Looking at the manual for the DI-514, this is probably :http://192.168.0.1". 3) The "Enable NetBIOS over TCP/IP" setting, if universally set to Default, is probably OK. But try changing them all to "Enable", just in case Ron is using SMB instead of NBT. I'm not done here yet, we've checked the most common solutions. I'll think a bit more, and see what else might be going wrong. Are you still getting "The network path was not found" when your Run "\\Ron"? That's at interesting odds with the CDiag for both Pavilion and Claudette: "net view Ron" Shared resources at Ron Ron's Computer - 11/26/04 - 1G Mem, 200G HD - $979.00 Share name Type Used as Comment ------------------------------------------------------------------------------- Apple IIe Disk EPSONSty Print EPSON Stylus Photo RX600 HP LaserJet 2100 PCL6 Print HP LaserJet 2100 PCL6 HP LaserJet 2100 Series PS Print HP LaserJet 2100 Series PS SharedDocs Disk The command completed successfully. Are all 3 computers in the same workgroup? What version - XP Home or Pro - on each? 4) An LSA: restrictanonymous = "1" or "2" would have been a good candidate for problem cause, a non-existent value is probably the same as a "0". Oh well. -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
#30
|
|||
|
|||
Cannot see 1 of 3 computers
On Thu, 3 Mar 2005 14:43:08 -0800, Ron Smith
wrote: Chuck, With all my checks and changes, the network seems to kind of drift in and out of operation -- but always in response to something I have done -- but always recoverable. Possible when I was getting Path not Found, it was one of the times when the network wasn't really quite working. But now, \\ron seems to be running on both computers B & C. It takes a while for the screen to come up, but a window pops up with "Ron's Computer -- 11/26/04 - 1GMem, 200G HD - $979.00 (ron)" in the Blue Window Frame at the top of the window. (This is the Computer description in Ron, except for the (ron) at the end.) Also, I didn't notice this before because the window pops up with the verbage on the left side of the screen, but when I click on the folders, and see the folders breakdown on the left, I see the Ron computer under the Network Places\....\Mshome\, (with the name above) along with claudette and pavilion. Also, under the computer name, I see an Apple IIe folder (an emulator - my son's work), a Shared Docs folder and a Printers and Faxes icon. That seems correct, as I marked the Apple IIe as shared, since I knew it didn't exist on the other computers and it would therefore help me to know I was looking at the Ron computer. This should be an important clue, shouldn't it. Ron, So the current symptom is simply that Ron doesn't show up in Network Places, until you manually do "\\Ron", at which time it opens up in the pop-up window, then mysteriously shows up in Network Places? How long can you see Ron in Network Places after that? When does this stop working? If you do this from Pavilion, how about you check Network Places on Claudette, and see what shows? Vice versa? Let's look at browstat information for each computer, again. Start - Run - "cmd". Type "browstat status c:\browstat.txt" into the command window - Open Notepad, make sure that Format - Word Wrap is NOT checked!, Open c:\browstat.txt, copy and paste into your next post. -- Cheers, Chuck Paranoia comes from experience - and is not necessarily a bad thing. My email is AT DOT actual address pchuck sonic net. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Can't Browse Networked Computers With Win XP Pro SP2 | pareez | Windows Service Pack 2 | 2 | August 12th 04 07:50 AM |
how to find other computers connected to the same router | AG Young | Networking and the Internet with Windows XP | 7 | July 30th 04 03:49 AM |
how to find other computers connected to the same router | AG Young | Networking and the Internet with Windows XP | 16 | July 30th 04 03:19 AM |
how to find other computers connected to the same router | AG Young | Networking and the Internet with Windows XP | 26 | July 29th 04 09:49 PM |
how to find other computers connected to the same router | AG Young | Networking and the Internet with Windows XP | 3 | July 29th 04 11:57 AM |